[T3] Alignment

Wed Dec 14 19:31:44 PST 2016

Wish there was a LIKE button.
You raise a good point! :-)

-----Original Message-----
From: type3-vwtype3.org [mailto:type3-vwtype3.org-bounces at lists.vwtype3.org] On Behalf Of William J
Sent: Wednesday, December 14, 2016 7:12 PM
To: type3 at vwtype3.org
Subject: Re: [T3] Alignment

I've been told here I worry so much , well I'm beat now by far.

 I've read all of these alignment posts and what stands out most to me is the 7K trip you took with all the added cargo weight which could very well have caused that tire to wear as it did. That trip was up and down hills and turns with all the added weight which in itself places weight on different tires and takes it off others.

 I have far more miles on my tires than you have and all original parts in the rear and front other than the tie rod ends . I wore one set of rears years ago both on the inside where the steel belts were showing and was told when I got new tires one front original shock was bad RF so I replaced all with gas shocks large white in the rear and small silver on the front and never had a tire wear issue again .

 I have no idea if the shocks solved the problem of if was just crappy tires . All I do recall is the rear tires were wider than the front because I bought what was available local think they were 185 x15 and perhaps that was the reason. Who knows . I check the tire pressure and one day came out of work to find a flat then saw the steel belts showing .

 Personally I would take a look at the tires you have now to see how they are wearing and write down the milage . An alignment means nothing when you have extra weight in the car because everything changes . It should be done with the driver in the car and anything else you usually carry , if not then it will be off.
----- Original Message -----
From: "Daniel Nohejl" <d.nohejl at gmail.com>
To: <type3 at vwtype3.org>
Sent: Wednesday, December 14, 2016 2:27 PM
Subject: Re: [T3] Alignment

> It took a little less than 40k miles for the tire to wear out on the 
> inner edge. What I don’t know is exactly when it started wearing.
>
> I got the tires rotated (front to back/back to front) and a 4 wheel 
> alignment on July 1st of this year. Then we went on a cross-country 
> drive of more than 7k miles. I never noticed the tire wearing like 
> that when it was in the front, but it may have started then 
> (unbeknownst to me as I didn’t even notice the tire was worn out until 
> I had it off for unrelated
> reasons) and then finished wearing in the back. Alternatively, it 
> might not have started to wear badly until it was rotated to the back. 
> I’ll have to inspect my new tires this weekend and see if I notice any unusual wear.
>
>
> Daniel
>
>
>
>
>
>> On Dec 14, 2016, at 4:00 PM, Daniel K. Du Vall 
>> <dduvall at 1peter4-10.org>
>> wrote:
>>
>> How long did it take to wear the tire out on the inner edge?
>>
>> I would still say that there is a fair amount of toe out on that side 
>> assuming its only one side.
>>
>> Toe out causes a tire to scuff as it roles on the inner side of a 
>> tire and toe in is the opposite.
>>
>> All our AC VW have a some amount of negative camber but if lowered, 
>> which I assume not in your case, increases the amount of negative camber.
>>
>> The more toe in combined with negative camber would cause that sort 
>> of wear in your picture.
>>
>>
>> Far as the bushings assuming they are the OEM rubber ones Jim's right 
>> in that its more than likely not the cause.
>>
>> The Red urethane ones would state some one has replaced them and 
>> doubtful that they have worn enough to cause this also.
>>
>> The red ones should be visible without any disassembly but maybe a 
>> bit of cleaning.
>>
>> Here is a link that show both types:
>>
>>
>> http://www.mamotorworks.com/VW/subcategory/rear-suspension-bushings
>>
>> Air Cooled Volkswagen Rear Spring Plate Bushings From Mid 
>> ...<http://www.mamotorworks.com/VW/subcategory/rear-suspension-bushin
>> gs>
>> www.mamotorworks.com
>> This Air Cooled VW Rubber Rear Spring Plate Bushing set is made of a 
>> soft rubber like the OEM bushings used originally. 4 piece car set
>>
>>
>>
>> ________________________________
>> From: type3-vwtype3.org <type3-vwtype3.org-bounces at lists.vwtype3.org> 
>> on behalf of Jim Adney <jadney at VWType3.org>
>> Sent: Wednesday, December 14, 2016 1:21:57 PM
>> To: type3 at vwtype3.org
>> Subject: Re: [T3] Alignment
>>
>> On 13 Dec 2016 at 19:04, Daniel Nohejl wrote:
>>
>>> Okay, so I found my notes from 2013 and it looks like 4 NOS spring 
>>> plate bushings were installed in the summer of that year. Does the 
>>> fact that one of those is squeaking mean anything at all? My 
>>> impression is that the OEM rubber ones aren´t supposed to squeak. Of 
>>> course NOS does include the word "old" in it so perhaps they were 
>>> past their prime. In any case, that does mean that the diagonal arm 
>>> bushings are original.
>>
>> The spring plate bushings are intended to "squirm" internally. If 
>> they slip, either inside or outside, they will wear and fail. The 
>> squeak you're hearing could be from slipping, or it could be from 
>> metal to metal contact somewhere.
>>
>> As Keith mentioned, the OE bushings are a real bear to install, 
>> because they are so tight. I suspect that the polyurethane 
>> replacements are made slightly smaller, so they will be easy to 
>> install, but that makes them likely to slip and wear, so I'm 
>> skeptical about their long term reliability.
>>
>> In 45 years, the ONLY diagonal arm bushings I've ever replaced were 
>> on one side of a '71 squareback where someone had removed the pivot 
>> bolt and neglected to put it back. Left unconstrained for years, the 
>> bushings ran into something else and got distorted to the point where 
>> a replacement pivot bolt would not go in. I had to remove the old 
>> bushings and install new ones to restore the rear suspension 
>> geometry. The owner admitted that this quieted down the ride 
>> significantly, now that the diagonal arm was no longer banging around 
>> back there.
>>
>> In other words, I doubt if there's any problem with your diagonal arm 
>> bushings, assuming the pivot bolt is in place.
>>
>> --
>> *******************************
>> Jim Adney, jadney at vwtype3.org
>> Madison, Wisconsin, USA
>> *******************************
>>
>> _______________________________________________
>> VWType3.Org mailing list - type3 at vwtype3.org To unsubscribe or change 
>> subscription options, visit:
>> http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org
>> If you need more help, contact: gregm at vwtype3.org
>> -------------- next part -------------- An HTML attachment was 
>> scrubbed...
>> URL: 
>> <http://lists.vwtype3.org/pipermail/type3-vwtype3.org/attachments/201
>> 61214/ff3a15d5/attachment.htm> 
>> _______________________________________________
>> VWType3.Org mailing list - type3 at vwtype3.org To unsubscribe or change 
>> subscription options, visit:
>> http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org
>> If you need more help, contact: gregm at vwtype3.org
>
> _______________________________________________
> VWType3.Org mailing list - type3 at vwtype3.org To unsubscribe or change 
> subscription options, visit:
> http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org
> If you need more help, contact: gregm at vwtype3.org
> 

---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus

_______________________________________________
VWType3.Org mailing list - type3 at vwtype3.org To unsubscribe or change subscription options, visit:
http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org
If you need more help, contact: gregm at vwtype3.org