<div dir="ltr">As a follow up, that most certainly helped.  The alignment was not far off, but with the nylon cable ties on, I can now get my idle down to 850.  Prior to installing the ties, the lowest idle speed I could get was around 1050 with the idle adjustment all the way closed.<br>
</div><div class="gmail_extra"><br><br><div class="gmail_quote">On Mon, Aug 5, 2013 at 6:58 AM, Jacob Adam Schroeder <span dir="ltr"><<a href="mailto:jacob.schroeder@gmail.com" target="_blank">jacob.schroeder@gmail.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr">Great, thanks Jim.  I will give this a shot over the weekend.  My suspicion is that my 15-year-younger self was probably a little sloppy on aligning these when I put the engine together years ago.<br>
</div><div class="HOEnZb"><div class="h5"><div class="gmail_extra">
<br><br><div class="gmail_quote">On Sun, Aug 4, 2013 at 7:42 PM, Jim Adney <span dir="ltr"><<a href="mailto:jadney@vwtype3.org" target="_blank">jadney@vwtype3.org</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">

<div>On 4 Aug 2013 at 16:20, Jacob Adam Schroeder wrote:<br>
<br>
> I know that my 4 intake manifold seals are bad and in need of replacement.<br>
> I have been "getting by" by turning them and manipulating them just so<br>
> until I can tell there is no leak, but once they get disturbed, it is<br>
> getting harder and harder to get a good seal.<br>
<br>
</div>Start by sliding each tube back onto the air runner, then loosen all<br>
the bolts that hold both air runners and the IAD. Move things around<br>
until you get the best alignment of all the tubes. Tighten all the<br>
bolts. Then bend the air runner tubes to make the alignment of each<br>
one perfect. They only take a medium amount of force to bend.<br>
<br>
Then slide the tube seals back in place. If the tubes are distorted<br>
so much that they won't seal now, tighten nylon cable ties around any<br>
joint that leaks. In a couple years you may be able to remove the<br>
cable ties.<br>
<br>
Don't use hose clamps. They are too tight, will tear up the tubes,<br>
and will not allow things to slide as the engine expands and<br>
contracts with temp changes.<br>
<div><br>
> Are there readily available and acceptable replacements?<br>
<br>
</div>Probably. I think Bob has made some, and I may have some good used<br>
ones. With proper assembly, which is very seldom done, they are never<br>
needed.<br>
<div><br>
> Is this a job I can do with the engine in the car?<br>
<br>
</div>Yes.<br>
<span><font color="#888888"><br>
--<br>
*******************************<br>
Jim Adney, <a href="mailto:jadney@vwtype3.org" target="_blank">jadney@vwtype3.org</a><br>
Madison, Wisconsin, USA<br>
*******************************<br>
<br>
_______________________________________________<br>
VWType3.Org mailing list - <a href="mailto:type3@vwtype3.org" target="_blank">type3@vwtype3.org</a><br>
<a href="http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org" target="_blank">http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org</a><br>
Contact <a href="mailto:gregm@vwtype3.org" target="_blank">gregm@vwtype3.org</a> if you need help with the list.<br>
</font></span></blockquote></div><br></div>
</div></div></blockquote></div><br></div>