<div dir="ltr">Have you checked that is is properly grounded? A bad ground can cause a jumpy needle. I have one myself. <div><br></div><div>Adam</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Thu, May 28, 2015 at 6:00 PM, Jacob Adam Schroeder <span dir="ltr"><<a href="mailto:jacob.schroeder@gmail.com" target="_blank">jacob.schroeder@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Also, I saw the fix that somebody shared previously about drilling a hole<br>
in the center of the sender.  That was interesting but I'd prefer not to<br>
make that mod if I can avoid it.<br>
<div><div class="h5"><br>
On Thu, May 28, 2015 at 3:58 PM, Jacob Adam Schroeder <<br>
<a href="mailto:jacob.schroeder@gmail.com">jacob.schroeder@gmail.com</a>> wrote:<br>
<br>
> I have a 1972 Squareback and have been having a recent issue with my fuel<br>
> gauge.  I recall the the gauge used to work, so I am not sure what has<br>
> changed over time.<br>
><br>
> The gauge appears to be accurate, when it is steady.  But the problem I<br>
> have is that the needle jumps around like crazy (especially when I am<br>
> driving).  From looking at the gauge, it appears that there are two ground<br>
> points: (1) through the housing to the spring clips to the dash, and (2) a<br>
> ground wire to the back of the gauge through the black plastic piece that<br>
> clips on to the rear of the gauge.<br>
><br>
> Are these grounds redundant in that only one has to be good?  Do both<br>
> grounds service the fuel gauge or is the wire for the lights and the fuel<br>
> gauge grounds through the clips?<br>
><br>
> The bouncing needle to me indicates a grounding problem, but I cannot seem<br>
> to track it down.<br>
><br>
> Also, I followed the test in Bentley--disconnecting the sender and<br>
> grounding the wire to the sender housing, and the gauge reads full.  So,<br>
> according to Bentley, the sender is good.  I tested a spare sender and get<br>
> the same jumpy needle.  So I am fairly confident my sender is OK.  But, do<br>
> the late (1972) sending units need a tab of exposed metal on the tank for<br>
> grounding?  I saw something to that effect in Bentley and I did repaint my<br>
> tank within the past few years, but did not leave a portion of exposed<br>
> metal along the circumference of where the sending unit mounts to the tank.<br>
><br>
> Also, could be unrelated, but I also get an intermittent fast turn signal<br>
> blink that may share a similar cause.<br>
><br>
> Any help would be appreciated.  Thanks,<br>
><br>
> Jacob<br>
><br>
><br>
-------------- next part --------------<br>
An HTML attachment was scrubbed...<br>
</div></div>URL: <<a href="http://lists.vwtype3.org/pipermail/type3-vwtype3.org/attachments/20150528/ce54d4d9/attachment.htm" target="_blank">http://lists.vwtype3.org/pipermail/type3-vwtype3.org/attachments/20150528/ce54d4d9/attachment.htm</a>><br>
<div class="HOEnZb"><div class="h5">_______________________________________________<br>
VWType3.Org mailing list - <a href="mailto:type3@vwtype3.org">type3@vwtype3.org</a><br>
To unsubscribe or change subscription options, visit:<br>
<a href="http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org" target="_blank">http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org</a><br>
If you need more help, contact: <a href="mailto:gregm@vwtype3.org">gregm@vwtype3.org</a><br>
</div></div></blockquote></div><br></div>