<div dir="ltr">I haven't used braided fuel line in years. I had 7 mm German none braided line on the engine for 10 years I don't know what fuel it's rated for Bus Depot is where I got it . I replaced all but under the tank with Gates Barricade FI hose I will handle ethanol fuels yet it's real difficult to get over the two metal rails to the injectors since the barb is so large . I used the Swiss made FI clamps on the engine which I used for the German hose and bought more of the same for the rest of the lines , they don't cut into the hose like the hardware of FLAPS regular hose clamps. I've used those before with out issue yet once you look at the hose after they do cut into the hose. <br></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Fri, Jun 28, 2019 at 9:09 AM Jim Adney <<a href="mailto:jadney@vwtype3.org">jadney@vwtype3.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">On 27 Jun 2019 at 22:42, Soren Jacobsen wrote:<br>
<br>
> I hate to admit it, but I've avoided using modern fuel hose in my<br>
> engine compartments because I simply can't stand the look of it and<br>
> the engine compartment is the most aesthetically important area of the<br>
> car to me.  I've also been troubled by the "oh, just use some Good<br>
> Quality quarter inch hose and clamp the hell out of it" mindset.  I'd<br>
> much rather have something that fits to begin with.  I replace braided<br>
> fuel hose every couple years, though; doesn't cost much or take very<br>
> much effort, and under this maintenance schedule I've never taken off<br>
> a hose that looked scary.  Perhaps I'm lucky, or the local fuels are<br>
> relatively benign.  I've heard of people having rotten braided lines<br>
> as soon as a year after installation.<br>
<br>
Most of you don't remember what the FI engines looked like when they were <br>
new. Yes, the hoses had exposed braid, but that was covered by some grey <br>
vinyl sleeving that made the exposed braid invisible except at the very ends, <br>
where the single-loop Oetiker hose clamps were. There was very little braid <br>
visible and no screw type hose clamps of any kind.<br>
<br>
I'd LOVE to find a source for grey vinyl sleeving, because I suspect that it <br>
provided one more layer of heat shielding that kept the gas from boiling <br>
during the heat soak after shutdown. I actually have a roll of vinyl sleeving <br>
that I bought years ago from VW as replacement, but that came in black <br>
instead of grey. Maybe it would work the same, or maybe the black color <br>
would absorb heat faster than grey. Who knows what this looks like in IR <br>
(Infra Red?) I haven't tried it. Just lazy, I guess.<br>
<br>
> Anyway!  With that confession out of the way, I recently stumbled upon<br>
> some properly-sized (for the earlier cars that I'm most interested in)<br>
> fuel hose.  I ordered some, but it hasn't yet arrived.  It's pretty<br>
> expensive, but I figure if it lasts a decade (under the car where no<br>
> one can see it -- I won't be installing this in any engine<br>
> compartments, because ew bare rubber!) who cares about the cost: <br>
> <br>
> <a href="http://www.volksbolts.com/faq/fuelhose.htm" rel="noreferrer" target="_blank">http://www.volksbolts.com/faq/fuelhose.htm</a><br>
<br>
This is a really interesting web page. They've done a great job of condensing <br>
the SAE hose specs down to the essential stuff. It looks like R6 or R7 would <br>
be fine, but R9 would be better and R14 would be excellent. Too bad no one <br>
bothered to proof read the page, as there are a number of typos, and they <br>
substitued permitivity for permeability, which is completely wrong.<br>
<br>
> There's also this braided stuff, which I haven't bought yet but probably will in the near future:<br>
> <br>
> <a href="https://www.belmetric.com/multifuel-hoseethanol-approved-c-14_662/rhm5braid-flennor-multifuel-hose-5mm-braided-p-9852.html" rel="noreferrer" target="_blank">https://www.belmetric.com/multifuel-hoseethanol-approved-c-14_662/rhm5braid-flennor-multifuel-hose-5mm-braided-p-9852.html</a><br>
<br>
You'd have to buy the 5 mm stuff to fit on your 6 mm fittings, which is a 20% <br>
stretch, whereas 10% stretch is the max recommended. Our original 7 mm FI <br>
hoses tended to fail where they were stretched over 8 mm tubing, so VW <br>
changed to 7.5 mm hose. I now use 8 mm hose, which I can get away with <br>
because of the 8.? bulges in most of the fittings. There are a few straight 8 <br>
mm fittings, but only 2 that are under pressure. Those take extra care (full <br>
circle clamps) to seal reliably.<br>
<br>
-- <br>
*******************************<br>
Jim Adney, <a href="mailto:jadney@vwtype3.org" target="_blank">jadney@vwtype3.org</a><br>
Madison, Wisconsin, USA<br>
*******************************<br>
<br>
_______________________________________________<br>
VWType3.Org mailing list - <a href="mailto:type3@vwtype3.org" target="_blank">type3@vwtype3.org</a><br>
To unsubscribe or change subscription options, visit:<br>
<a href="http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org" rel="noreferrer" target="_blank">http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org</a><br>
If you need more help, contact: <a href="mailto:gregm@vwtype3.org" target="_blank">gregm@vwtype3.org</a><br>
</blockquote></div>