<div dir="ltr"><div>When I removed the large breather cap there was some oil film inside the inner part of that cap yet I think that's normal and there was no white foam like moisture in the oil . I read on rennlist about the slop where the trigger points mount that it should be set to the center point since it will alter the point when the injectors fire . I have a pertronix and always set it toward the advanced point yet it ran fine for decades like this perhaps with points it might make a difference. It ran fine even with the lousy EMPI exhaust system and back then even with the leak on the right heat ex changer same when I had the J pipes it never popped out the exhaust with both sensors connected. I repaired the AAR since  it was not closing fully and would make it rich plus the idle was high or low that helped with the idle. Pertronix told me these units can fail by not working or fail where it can cause a miss yet that does not explain why it does not miss with the air temp unplugged. <br></div><div><br></div><div> I thought for sure once I replaced all the vacuum lines and runner boots , sealed the IAD back cover and all the other work it would fix this issue yet it changed nothing. I replaced the plugs , the Bosch plugs I removed after 1500 miles looked dry -black sooty like it was running rich yet I've read with the new fuel this does not offer much , whether true or not I have no idea. From all I've read popping out the exhaust indicates a rich condition with or with out an exhaust leak. I've also read it can be caused by a lean condition. <br></div><div><br></div><div> The only thing that makes sense in my mind is either there is a voltage drop to the ECU from the power relay or high resistance in the air temp sensor wires to the ECU or perhaps the head temp sensor to ECU or the air temp sensor itself is erratic when connected. I haven't read or any going bad . I've checked the fuel pressure several times and it's always 30 PSI . The Bentley states 28 to 31 PSI yet only check it and adjust it if out of this range , the earlier models state 28 PSI . Maybe I should bring it back down to 28 PSI because this does have an affect on how rich it runs and 28 to 31 PSI is spec for even later models not just 68 and 69 .<br></div><div><br></div><div> I even connected a vacuum gauge teed into the MPS line and it's steady , once I plug in the air temp it becomes erratic so at that point the MPS does not have a steady vacuum applied which would cause it to alter the injector timing making it run uneven as it does. <br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Sep 10, 2019 at 5:58 AM Jim Adney <<a href="mailto:jadney@vwtype3.org">jadney@vwtype3.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">On 9 Sep 2019 at 16:06, William Jahn wrote:<br>
<br>
> Any suggestions on what I should look for and do? I don't think it's<br>
> affecting the fuel to air mix yet anything is possible. I know the PCV has<br>
> been NLA for a good long time.<br>
<br>
How about checking the voltage drop across the fuel pump relay while the <br>
engine is running? That's the same part as used for the main power relay <br>
and if it had also developed a problem, that would reduce the power to the <br>
pump, possibly leading to low fuel pressure and lean running.<br>
<br>
The PCV valve is easy to remove and clean, but they very seldom get so <br>
gunked up that it's a problem. You'll never need a new one.<br>
<br>
-- <br>
*******************************<br>
Jim Adney, <a href="mailto:jadney@vwtype3.org" target="_blank">jadney@vwtype3.org</a><br>
Madison, Wisconsin, USA<br>
*******************************<br>
<br>
_______________________________________________<br>
VWType3.Org mailing list - <a href="mailto:type3@vwtype3.org" target="_blank">type3@vwtype3.org</a><br>
To unsubscribe or change subscription options, visit:<br>
<a href="http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org" rel="noreferrer" target="_blank">http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org</a><br>
If you need more help, contact: <a href="mailto:gregm@vwtype3.org" target="_blank">gregm@vwtype3.org</a><br>
</blockquote></div>