<div dir="ltr"><div>JIm ;</div><div><br></div><div> I do have a space ECU , I think I brought this up before. It came out of the 72 Square. Now that car was also an auto trans , it did not have the EGR and the ECU has no plate on it so I don't know if it's a late E or early E unit. I does however have the ground wire tab as well as the welded on mount for the thermal unit to tell the temp for the EGR when to operate. It's not like the earlier models it is for an E system. That's if for some odd reason the ECU in my car the 048 has an issue reading the air temp sensor. If I knew what pin 1 should read with the ECU unplugged I could check that. Yes I'm stabbing in the dark. <br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Fri, Sep 13, 2019 at 11:48 AM Jim Adney <<a href="mailto:jadney@vwtype3.org">jadney@vwtype3.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">On 13 Sep 2019 at 10:04, William Jahn wrote:<br>
<br>
>  What is the center conductor ?<br>
<br>
That's the copper strands in the middle. It's the only conductor in the wire, <br>
but the body and crimp form an outside conductor.<br>
<br>
> I only see a thin red wire when all the black  plastic covering is removed<br>
<br>
It's red on some, black on some. I think black was the original version, but it <br>
makes no functional difference.<br>
<br>
> In another post you said there is a spring on each end of the<br>
> thermister / small puck was your term. <br>
<br>
Probably more like a spring on one end and pushed against the body on the <br>
other end.<br>
<br>
> My point is is I were to short the lead anywhere from the connector to<br>
> the crimp to ground then this is a short to ground . You said from the<br>
> connector to the crimp should read say 1.8K ohm . <br>
<br>
Yes, this was in response to your post that said that you measured an open <br>
circuit between the connector and the crimp.<br>
<br>
> Or is the puck or thermistor in contact with the crimp at one end via a<br>
> small spring and also contacts the body via a spring at the other end?<br>
<br>
Yes, wire to small spring, to thermistor puck, to body. IIRC, the thermistor is <br>
a small cylinder, maybe 3/16" dia and 3/16" long.<br>
<br>
>  I already tightened all the injector connectors and all the other ones the<br>
> TPS and MPS and trigger points. None of this made any difference.<br>
<br>
Okay, good.<br>
<br>
-- <br>
*******************************<br>
Jim Adney, <a href="mailto:jadney@vwtype3.org" target="_blank">jadney@vwtype3.org</a><br>
Madison, Wisconsin, USA<br>
*******************************<br>
<br>
_______________________________________________<br>
VWType3.Org mailing list - <a href="mailto:type3@vwtype3.org" target="_blank">type3@vwtype3.org</a><br>
To unsubscribe or change subscription options, visit:<br>
<a href="http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org" rel="noreferrer" target="_blank">http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org</a><br>
If you need more help, contact: <a href="mailto:gregm@vwtype3.org" target="_blank">gregm@vwtype3.org</a><br>
</blockquote></div>