<div dir="ltr"><div>The two sets of Bosch wires I got seem to reach well enough though #1 could be a bit longer at least it wouldn't hurt if it had 2" more. I just laid them out so the longest ones where on #1 & #2  and they worked out , I have them in the breather tongue then in the holder hidden by the oil bath. In order to get the dist cap off enough to do points I lift them out of the breather top flap rather than pull them out of the cap. I got one set in 2015 and the first set in the mid 80's and they look the same yet the ones from the 80's have some nicks and worn flat spots on the outer grey cover nothing that caused any issues .</div><div><br></div><div> I'm pretty sure I have 1 and 2 in the right path from the cap over the breather tucked under the breather tab then down to the one double holder that's near the edge of the oil bath hidden with the oil bath in place then outside and over the fuel line and outside of  FI plug for #1. They sit away from the fuel injectors and fuel line metal manifold yet could be a bit further away more like they fit on 3 & 4, Those are plenty long . The shortest wire is #4 . I favored the cap booths so 1 & 2 face the right and it was just enough where they don't touch anything probably why I need to move them out of the breather to lift the cap away enough . I imagine Bosch depending on when they were made might have changed the lengths a bit the second set was made in Mexico. I would be easy to do as you did just keep the short one and cut the others and screw on the plug end . I don't have a great crimping tool for the cap or coil ends just a cheap all in one tool that have one for 7 and 8 mm wire it worked well enough for one crimp and I re used one of the one coil ends. Saw some on you tube you place in a vice. The better ones would be the ratcheting type and new cap ends that are 90 degree. NGK has a nice set yet they are $75 to $80 . The Bosch sets so far other than the coil wire have not been an issue seem well made and hold up can't say I like putting them in the old holders I have to be careful and lube them a bit them squeeze the wire so I don't cut into the outer jacket. <br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sat, Nov 9, 2019 at 5:20 PM Jim Adney <<a href="mailto:jadney@vwtype3.org">jadney@vwtype3.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">On 9 Nov 2019 at 10:01, William Jahn wrote:<br>
<br>
> If I at some point need another set I'd rather make my own although it<br>
> seems to cost more if one needs new plug ends and tin seals <br>
<br>
Once you've bought 2 sets, you should have enough parts to keep you <br>
going for years.<br>
<br>
I have any parts you might need, plus plenty of Belden SP wire to <br>
replace old wires that may have gotten hard and cracked. I find that <br>
the only parts that tend to need replacement over time are the wire <br>
and the occasional SP connector that goes open. The OG parts were <br>
exceptionally reliable.<br>
<br>
I have a few Bosch SP cable sets, but I've found that they didn't get <br>
the lengths right. None of them are long enough to reach #1 while <br>
running in the correct path. I have to make a new wire for #1, <br>
discard the shortest wire (or save it for someone's coil) and modify <br>
the others for 2, 3, and 4.<br>
<br>
-- <br>
*******************************<br>
Jim Adney, <a href="mailto:jadney@vwtype3.org" target="_blank">jadney@vwtype3.org</a><br>
Madison, Wisconsin, USA<br>
*******************************<br>
<br>
_______________________________________________<br>
VWType3.Org mailing list - <a href="mailto:type3@vwtype3.org" target="_blank">type3@vwtype3.org</a><br>
To unsubscribe or change subscription options, visit:<br>
<a href="http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org" rel="noreferrer" target="_blank">http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org</a><br>
If you need more help, contact: <a href="mailto:gregm@vwtype3.org" target="_blank">gregm@vwtype3.org</a><br>
</blockquote></div>