<div style="font-size:10pt;font-family:arial,helvetica,sans-serif;color:black;"><div style="font-family:arial,helvetica,sans-serif;font-size:10pt;color:black;">Those "plastic" under rear seat cable connectors are actually coated in <br>plastic. There is a steel piece inside them to grip the wire cables. I've cut <br>one open, as I was trying to save the actual cable itself before.<br><br>On the flap ends in a beetle, there's a pivoting steel block that the cable <br>goes thru that is attached to the flap. It uses a screw to secure it. IDK if <br>the t-3 uses something similar or not.<br>Bob<br><br><br>-----Original Message-----<br>From: William Jahn <willjahn975@gmail.com><br>To: type3 <type3@vwtype3.org><br>Sent: Sat, Dec 28, 2019 9:58 pm<br>Subject: [T3] Heater cable connectors ?<br><br></div><div dir="ltr">I  replaced my front heater cables from the heat/defrost lever . I wanted<br></div><div dir="ltr">to know if the connectors that you connect the cables together like the<br></div><div dir="ltr">ones used for the rear foot wells they hold the two cable ends together and<br></div><div dir="ltr">also are an adjustment of the cable length are still available .<br></div><div dir="ltr"><br></div><div dir="ltr"> Mine seem fine yet I didn't know they were plastic. In case I need them is<br></div><div dir="ltr">there something like these that can be used?<br></div><div dir="ltr"><br></div><div dir="ltr"> It was a tough job replacing these. I used late beetle cables they are<br></div><div dir="ltr">about 20" longer . The right one was broken about 16" from the connector<br></div><div dir="ltr">under the tin cover on the floor. The old ones had bent over ends I had to<br></div><div dir="ltr">bend the new ones over just to get them through the tubes/conduit because<br></div><div dir="ltr">they were just cut ends yet I didn't make these bends after , I just fit<br></div><div dir="ltr">them in and adjusted and cut the extra length off . I left a bit over an<br></div><div dir="ltr">inch out past the connector if I need to make bends or fold them over. I<br></div><div dir="ltr">didn't strip them just enough to clamp the two cables to hold. I never<br></div><div dir="ltr">really looked at the rear ones don't know if they are also plastic with<br></div><div dir="ltr">brass screws and a brass base inside the plastic.<br></div><div dir="ltr"><br></div><div dir="ltr">William<br></div><div dir="ltr">-------------- next part --------------<br></div><div dir="ltr">An HTML attachment was scrubbed...<br></div><div dir="ltr">URL: <<a target="_blank" rel="noopener noreferrer" href="http://lists.vwtype3.org/pipermail/type3-vwtype3.org/attachments/20191228/edbc508b/attachment.html">http://lists.vwtype3.org/pipermail/type3-vwtype3.org/attachments/20191228/edbc508b/attachment.html</a>><br></div><div dir="ltr">_______________________________________________<br></div><div dir="ltr">VWType3.Org mailing list - <a ymailto="mailto:type3@vwtype3.org" rel="noopener noreferrer" href="mailto:type3@vwtype3.org">type3@vwtype3.org</a><br></div><div dir="ltr">To unsubscribe or change subscription options, visit:<br></div><div dir="ltr"><a target="_blank" rel="noopener noreferrer" href="http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org">http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org</a><br></div><div dir="ltr">If you need more help, contact: <a ymailto="mailto:gregm@vwtype3.org" rel="noopener noreferrer" href="mailto:gregm@vwtype3.org">gregm@vwtype3.org</a><br></div></div>