<div dir="ltr"><div>I didn't want to start a debate whether choosing to use the factory setup or gauges. It's a matter of personal choice. I just feel I know more of whats going on with gauges even if they are not dead on accurate. Long ago part of VW's testing was to connect a good mechanical gauge to the cooler and check it , think it was based on SAE30 158* oil temp at 2,500 rpm should be 28PSI . Lets just say as an example your hauling down the freeway it's 100 degrees and the oil light is off . What does this really tell you. that light will be off with 5PSI at 2,500 RPM . Now perhaps that's enough pressure to keep the engine alive I couldn't say yet I would venture to say it's far from ideal. Now If you actually checked the oil pressure every so often then you would know. Nothing is a given because at any time the pressure could drop for whatever reason. I just choose to be able to see this. And just to point out I don't see the German oil pressure switches offered all I see are after market hopefuls. Without testing the lights sender you don't know at what PSI it kicks on the light. Then there is always the light , you key on it lights start it goes out you know the swich grounds the light at 6 PSI . The only time you actually know the light bulb works is then or if it comes on . If it burnt out which is very rare yet not impossible you have nothing .  I did have just the oil pressure switch when I got my 73 and was fine with it. Then it began to leak so I chose to add gauges. I only added a voltmeter at first that doesn't affect the gen light. <br></div><div><br></div><div> I'm sure there are more VW's on the road with just the factory lights doing just fine. A 66 bug I owned just had the light the engine leaked oil like mad and I kept 3 quarts with me and not checking the level one day the light came on I pulled  over had to add 2 quarts. Didn't hurt the engine yet would have if I didn't see the light. <br></div><div><br></div><div> The point I'm trying to make is yes VW had their  reasons for just a light and that's fine. I just feel there are better options.<br></div><div>  </div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sun, Jul 19, 2020 at 9:51 AM William Jahn <<a href="mailto:willjahn975@gmail.com">willjahn975@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr">Yes he did , and I understand how this works. And this has to do with oil weight and of course bearing clearance. I use SAE 40 even when I rebuilt this engine and on a hot freeway run I'd come to a stop and the oil light would come on. This is why I didn't go down to SAE 30 , 30 may be fine <br></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sun, Jul 19, 2020 at 9:42 AM Mike Fisher <<a href="mailto:fisherfarms@gmail.com" target="_blank">fisherfarms@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Jim told us that oil pressure isn't important.  It's the oil flow?<br>
<br>
On Sun, Jul 19, 2020 at 9:38 AM William Jahn <<a href="mailto:willjahn975@gmail.com" target="_blank">willjahn975@gmail.com</a>> wrote:<br>
<br>
> The only thing I don't quite understand is on what basis has anyone tested<br>
> these gauges to say for certain they are not accurate or at least very<br>
> close to being so. The only true way to know would be to use a good screw<br>
> in oil pressure gauge on the cooler fitting and check that against what the<br>
> electric VDO setup reads.<br>
><br>
>  I feel as long as the wiring to the senders and gauges is done properly<br>
> and the grounds are done properly they will be as good as they can get.<br>
>  I know my old oil pressure gauge had issues because just with the key on<br>
> the gauge read 10 PSI and the sender should read 10 OHM engine off , my old<br>
> one read from 9.5 ohm to over 95 ohm just by tapping it with my fingers .<br>
> The new one stays at 10 ohm engine off . It reads completely different from<br>
> the old ones.  Before this I even replaced the wiring and put the ground on<br>
> the battery to the rear seat wall ground . None of that changed a thing. I<br>
> added inline fuses to the gauges between the fuse box and battery positive<br>
> on the gauges just in case and use a relay for the power source. When I<br>
> first installed them direct to a spare key on fuse on a 73 that's #12 they<br>
> didn't seem to read proper so I used a 12 volt relay used fuse 9 hot all<br>
> the time that powers that insane key buzzer for the feed source then fuse<br>
> 12 to the relay coil and that fixed the issue.<br>
><br>
> On Sun, Jul 19, 2020 at 8:56 AM Hal Sullivan <<a href="mailto:tristessa@tristessa.us" target="_blank">tristessa@tristessa.us</a>><br>
> wrote:<br>
><br>
> > On 7/18/20 11:55 PM, William Jahn wrote:<br>
> > >   I  can't recall a car or truck I ever had that didn't have at the<br>
> very<br>
> > > least a water temp and oil pressure gauge as well as a light or two.<br>
> > ><br>
> > I inherited an '81 Ford Escort from my grandmother in the late '90s,<br>
> > back before our first ACVW.  It had a speedometer, a gas gauge and some<br>
> > idiot lights.<br>
> ><br>
> ><br>
> > I'll take an electric oil pressure gauge over no gauge any day of the<br>
> > week.  Even without absolute accuracy, they're useful for spotting<br>
> > problems before they really become PROBLEMS .<br>
> ><br>
> > _______________________________________________<br>
> > VWType3.Org mailing list - <a href="mailto:type3@vwtype3.org" target="_blank">type3@vwtype3.org</a><br>
> > To unsubscribe or change subscription options, visit:<br>
> > <a href="http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org" rel="noreferrer" target="_blank">http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org</a><br>
> > If you need more help, contact: <a href="mailto:gregm@vwtype3.org" target="_blank">gregm@vwtype3.org</a><br>
> ><br>
> -------------- next part --------------<br>
> An HTML attachment was scrubbed...<br>
> URL: <<br>
> <a href="http://lists.vwtype3.org/pipermail/type3-vwtype3.org/attachments/20200719/15d285c9/attachment.html" rel="noreferrer" target="_blank">http://lists.vwtype3.org/pipermail/type3-vwtype3.org/attachments/20200719/15d285c9/attachment.html</a><br>
> ><br>
> _______________________________________________<br>
> VWType3.Org mailing list - <a href="mailto:type3@vwtype3.org" target="_blank">type3@vwtype3.org</a><br>
> To unsubscribe or change subscription options, visit:<br>
> <a href="http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org" rel="noreferrer" target="_blank">http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org</a><br>
> If you need more help, contact: <a href="mailto:gregm@vwtype3.org" target="_blank">gregm@vwtype3.org</a><br>
><br>
<br>
<br>
-- <br>
Eugene, Oregon<br>
<br>
<a href="http://s169.photobucket.com/albums/u236/mr_bojangles500/" rel="noreferrer" target="_blank">http://s169.photobucket.com/albums/u236/mr_bojangles500/</a><br>
-------------- next part --------------<br>
An HTML attachment was scrubbed...<br>
URL: <<a href="http://lists.vwtype3.org/pipermail/type3-vwtype3.org/attachments/20200719/2c174a72/attachment.html" rel="noreferrer" target="_blank">http://lists.vwtype3.org/pipermail/type3-vwtype3.org/attachments/20200719/2c174a72/attachment.html</a>><br>
_______________________________________________<br>
VWType3.Org mailing list - <a href="mailto:type3@vwtype3.org" target="_blank">type3@vwtype3.org</a><br>
To unsubscribe or change subscription options, visit:<br>
<a href="http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org" rel="noreferrer" target="_blank">http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org</a><br>
If you need more help, contact: <a href="mailto:gregm@vwtype3.org" target="_blank">gregm@vwtype3.org</a><br>
</blockquote></div>
</blockquote></div>