<div dir="ltr"><div>To clarify : With the timing set @ 5 BTDC and the vacuum advance connected it will ping which it never used to. The flat top pistons increase the compression ratio . When I set it close to TDC without the vacuum line connected it felt like it had more pep. This was when I removed the Pertronix and put back points so I had to reset the timing. I haven't set it @ TDC and tried the advance. I'd set the timing  @ 5 BTDC and drive it no vacuum advance and it pinged so I backed it off to 3 BTDC and it stopped then I connected the vacuum line and once it was warmed up it pinged. I just left it there and plugged the vacuum line. I feel 5 BTDC is correct yet it does not work out well since it pings. It's either the flat top pistons or the fuel or a combination. <br></div><div><br></div><div> I've read you lower the RPM to 850 engine warm and set the timing . My mechanical advance does not kick in until over 1,000 RPM . If I recall I used to set it at 1,000 RPM with a timing light or just set the pointer on 5 BTDC then used a bulb and set it static rotating the dist till the bulb just came on. <br></div><div><br></div><div> Point being if your 73 is stock with the dished pistons the results would be different. I think that's why Russ suggested setting it @TDC , this was when I rebuilt this engine. Before I rebuilt the engine it had dished pistons and a good vacuum can and it worked fine. Since then they have altered the fuel we didn't have ethanol then. I see in the Bentley 7.3 and 7.7 compression. With  dished stock it's 7.3 don't know if the 7.7 was flat top they don't state this just the year.  My goal is no pinging with the best performance not numbers. <br></div><div><br></div><div> Before I installed the pertronix in 97 I always ran points yet got a deep pit that to remove it the regap worked yet part of the pit still existed , I would need to file through the pont hard surface. <br></div><div><br></div><div> The vacuum advance didn't make any difference @ idle yet it did offer much better pep on light throttle. I always set the points so both surfaces were hitting dead center. Rather than deal with filing I just replaced them and timed it static and it was always dead on with a timing light check. I didn't have one. I borrowed one . This was why the one fellow suggested pertronix because every 3,000 miles it began to miss because of the pits. Once I replaced them it ran fine. <br></div><div><br></div><div> I wasn't until 72 5 BTDC was introduced and they had the dual can to retard the spark at idle for emissions then did away with this in 73. If I recall most earlier years were TDC which were on the higher compression engines and many other early 70's 1600 FI <br> </div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Fri, Feb 12, 2021 at 7:06 AM Jim Adney <<a href="mailto:jadney@vwtype3.org">jadney@vwtype3.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">On 11 Feb 2021 at 21:44, William Jahn wrote:<br>
<br>
>  I've never bothered to file points. Don't they have a hard coating filing<br>
> past that and it's pretty thin , you file through that<br>
<br>
There's a layer, you can see it, and it's about 1 mm thick. There's plenty of <br>
material to file if you care to.<br>
<br>
>  The one issue is setting the timing. When I  rebuilt this engine I used<br>
> flat top pistons , Russ said at one point I should set it @ TDC rather<br>
> than 5 BTDC. I Always did and it was not an issue until I put the vacuum<br>
> advance line back.<br>
<br>
IIRC, you have a Calif, X-engine, FI/AT '73, same as mine. The vacuum <br>
advance should not make any difference at idle. It doesn't on mine. <br>
<br>
-- <br>
*******************************<br>
Jim Adney, <a href="mailto:jadney@vwtype3.org" target="_blank">jadney@vwtype3.org</a><br>
Madison, Wisconsin, USA<br>
*******************************<br>
<br>
_______________________________________________<br>
VWType3.Org mailing list - <a href="mailto:type3@vwtype3.org" target="_blank">type3@vwtype3.org</a><br>
To unsubscribe or change subscription options, visit:<br>
<a href="http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org" rel="noreferrer" target="_blank">http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org</a><br>
If you need more help, contact: <a href="mailto:gregm@vwtype3.org" target="_blank">gregm@vwtype3.org</a><br>
</blockquote></div>