<div dir="ltr"><div>I once held a thermometer right on the sump plate after the VDO gauge read 180 F with the engine shut down power to the coil unplugged key on so the gauge would read and they were very close. I read that Gene Berg said most of the VDO and other brands of oil temp gauge senders were not accurate in a certain range , and I can't recall off hand what the range was. I'm also not sure if he was referring to both the gauge and sender combined. Somewhere I read or saw on Youtube  after this happened that Berg updated this and said if you use the sender that is installed in the cooler bypass valve port in place of the threaded cap it would be much more accurate. I haven't looked at Berg's site to see if I could find that info. I also found info of a test using a thermometer down the T-3 oil fill pipe and it stated that the VDO sensor in the bypass port read the same. I didn't see these tests being done and haven't done them myself . Point is reading the oil temp down the filler pipe reads the oil temp of the sump oil. This means to me the sender in the sump plate in place of the drain plug are the same reading . <br></div><div><br></div><div> I'll test the new sender in boiling water to see what it reads in ohms because it works by variable resistance. VDO offers one test room temp.<br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Sep 7, 2021 at 6:58 AM Jim Adney <<a href="mailto:jadney@vwtype3.org">jadney@vwtype3.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">On 5 Sep 2021 at 9:52, William Jahn wrote:<br>
<br>
> I was stuck in traffic barely moving for over an hour and the oil temp<br>
> read just under 220 F the oil light would go on at idle , it was 94 F air<br>
> temp . If I put the auto trans in neutral the oil light would go out . I<br>
> checked the oil level later and was down 1/2 quart . Once I was able to<br>
> start moving the oil temps dropped .<br>
<br>
Given your situation, hot day, hot pavement, stop & go traffic (surrounded by <br>
other cars also shedding their excess engine heat, as well as the heat from <br>
their ACs) I don't see anything particularly unusual about what you <br>
observed. Your 220 F indicated temperature is probably not unusual for <br>
those conditions, but it can be informative to test your temp sensor in boiling <br>
water (212 F) to see how good the calibration is.  <br>
<br>
Putting the AT into N is the right thing to do: It reduces the load on the <br>
engine which means less waste heat to get rid of, plus it lets the idle speed <br>
increase a bit, providing a bit more cooling and a bit more oil pumped thru <br>
the engine and oil cooler. It's a zero effort solution.  <br>
<br>
Once you get moving, there's no longer stagnant hot exhaust air trapped <br>
under the car, plus there's turbulence that enhances the cooling of the <br>
underside of the engine.  <br>
<br>
-- <br>
*******************************<br>
Jim Adney, <a href="mailto:jadney@vwtype3.org" target="_blank">jadney@vwtype3.org</a><br>
Madison, Wisconsin, USA<br>
*******************************<br>
<br>
_______________________________________________<br>
VWType3.Org mailing list - <a href="mailto:type3@vwtype3.org" target="_blank">type3@vwtype3.org</a><br>
To unsubscribe or change subscription options, visit:<br>
<a href="http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org" rel="noreferrer" target="_blank">http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org</a><br>
If you need more help, contact: <a href="mailto:gregm@vwtype3.org" target="_blank">gregm@vwtype3.org</a><br>
</blockquote></div>