<div dir="ltr"><div>I was able to fit the 73 can on the 72 they were the same . I don't know for certain if early 72 distributors were different from late or if both were the same. I recall we talked about this once long ago. <br></div><div><br></div><div> I don't have a parts washer or parts washer fluid . <br></div><div><br></div><div> I only rebuilt the 73 AH and I know it was never apart. I could see at some point someone sprayed red grease all over the inside and it was difficult to get that out. Basically I used the steel shims that were in the trigger cam. They had no wear and looked new. I measured with a micrometer  and replaced the fiber one then measured the lower larger ones and replaced two with the new ones and a new fiber one just to get around .004" play. Then I put some grease on the trigger plate and installed it to see if the cam hit the trigger plate , it didn't.  That trigger plate had some wear but I had it in the 72 dist for many years and never took that one apart and that was most likely what caused the wear. I didn't know at the time . I never had one apart. <br></div><div><br></div><div> Once I get both the spares I have apart, if I need more steel shims that fit in the trigger cam I can use some to make a good dist. Right now I have no idea which one is better as far as shaft and sleeve bearing wear. However I think I have enough good parts from both to make one good one. <br></div><div><br></div><div> There is not much info on these FI type 3 distributors and I searched for weeks. My main concern with the felt is I have no idea how well the engines these came out of  had the oil changed which might introduce grit on the shaft and onto the lower bushing. The way you do it with parts washer fluid would get that felt pretty clean.  <br></div><div><br></div><div> I do appreciate the help. <br></div><div><br></div><div>William<br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Sep 13, 2022 at 8:41 PM <<a href="mailto:jadney@vwtype3.org">jadney@vwtype3.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">On 13 Sep 2022 at 12:24, William Jahn wrote:<br>
<br>
> What should I set the axial play at between the drive dog and dist body?<br>
<br>
I try to get the play as small as possible, without introducing any drag while turning. if there <br>
are not enough shims under the FI trigger cam, that cam will sit too low and rub on the trigger <br>
points plate, like one of the ones in your photo.<br>
<br>
For the felt, I leave it in place while I wash the dist body in parts washer fluid. After drying out, <br>
I add some oil, but mostly it will get reoiled when the engine runs, Parts washer fluid dries <br>
faster than water, but you can flush out the water with alcohol to speed things up.<br>
<br>
The '72 dist had vacuum advance/retard. The vacuum can mounting screws are offset to only <br>
accept that can, but you can drill/file new holes in a '73 can to get it to fit. I hate to see this, <br>
simply because it looks like kluge, but it works.<br>
<br>
-- <br>
*******************************<br>
Jim Adney, <a href="mailto:jadney@vwtype3.org" target="_blank">jadney@vwtype3.org</a><br>
Madison, Wisconsin, USA<br>
*******************************<br>
<br>
_______________________________________________<br>
VWType3.Org mailing list - <a href="mailto:type3@vwtype3.org" target="_blank">type3@vwtype3.org</a><br>
To unsubscribe or change subscription options, visit:<br>
<a href="http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org" rel="noreferrer" target="_blank">http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org</a><br>
If you need more help, contact: <a href="mailto:gregm@vwtype3.org" target="_blank">gregm@vwtype3.org</a><br>
</blockquote></div>