[T3] 65 Headlights
Keith Park
topnotch at nycap.rr.com
Mon Aug 22 20:14:10 PDT 2011
Ahh, I have 2 SB12 rings with the adjusters in them, but 2 sealed beam
bulbs, one was in a standard sealed beam bucket and the other looked like it
was hanging by the outer SB12 on its adjusters, perhaps cluged together.
The replacement fenders suggest as you did, both are post 65 as they didn't
have the side markers in them. Ill probably use the sealed beam units, and
the OEM SB12's with dummy screw heads in the adjusters so they look stock,
gotta keep the stock look... Gotta Rep I need to establish again!
Keith
Top Notch Restorations
topnotch at nycap.rr.com
http://www.a383ina68.addr.com/radiorest/main.htm
71 Squareback "Hothe"
65 Notchback "El Baja Rojo"
65 Squareback "Eggcrate"
87 golf "Winterat"
93 RX7 "Redstur"
-----Original Message-----
From: type3-vwtype3.org-bounces at lists.vwtype3.org
[mailto:type3-vwtype3.org-bounces at lists.vwtype3.org] On Behalf Of
Bobsnotch at aol.com
Sent: Monday, August 22, 2011 11:05 PM
To: type3 at vwtype3.org
Subject: Re: [T3] 65 Headlights
In a message dated 8/22/2011 10:11:19 P.M. Eastern Daylight Time,
topnotch at nycap.rr.com writes:
Hi all,
OK. whats the mounting situation on the '65 headlights, do they really
attach only to the outer SB12 trim rings and adjust their angle with the
diagonal screws that hold them on? Are they attached to the bucket
anywhere?
The OE fenders are so rotted I cant tell whats left, I have 2 NOS fronts
that are going on the car, one bucket has the standard late tabs for the
later bucket/adjuster assemblies but one only had a screw on the bottom
where the trim ring fastens and a mount on the very top.
Anyone have a picture of the correct 65 setup and how it works? Want to
use
the original type setup, I have two good trim rings but only the late
bucket/adjuster assemblies.
Thanks,
Keith
Keith, it sounds like you've got 1 sealed beam fender, and 1 euro spec
fender. You'll have to decide which style you want to use, unless you don't
have 2 of either type. Personally I'd go with sealed beams (more commonly
found parts available), but IF you have 2 complete euro assemblies, use
them,
and find some light bulbs to fit them. Note the euro assemblies won't be
cheap either. :O The sealed beam style uses 3 tabs to mount the bucket,
while
the euro assembly uses an all by itself bucket/headlight assembly to mount
the bulb holder-light assembly with adjustment built into the ring.
Bob 65 Notch S with sunroof and IRS (Krusty)
71 Notch (Krunchy)
64 T-34 Ghia (Wolfie)
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://lists.vwtype3.org/private.cgi/type3-vwtype3.org/attachments/20110822
/e19125b5/attachment.htm>
_______________________________________________
VWType3.Org mailing list - type3 at vwtype3.org
http://lists.vwtype3.org/listinfo.cgi/type3-vwtype3.org
Contact gregm at vwtype3.org if you need help with the list.
More information about the type3-vwtype3.org
mailing list